Star Tech Journal

Issue: 1990-January - Vol 11 Issue 11

Hantarex Replace-
nient Xsistors
Data East MoNite
F'ball Q54 Failure
Chris Richards
Coin-Op Inc.
Webb City, Missouri
Peter Gustafson
Data East Pinball
Melrose Park, Illinois
SYMPTOM
I recently had some problems with the red color
amplifier on a Hantarex MTC 9000. The red
input was totally saturated. No problem. I whip
out my schematic, find the transistor in the amp
section, check it out.
SUBJECT
Intermittent and repeated failure of Q54 on ABC
Monday Night Football CPU boards.
PROBLEM
Sure enough, had a collector to emitter short. So
I pulled out my handy dandy NIE reference and
crossed the transistor. It crossed to a 123AP
with the package rotated 180 degrees. This also
crossed for a 2N2222, 2N3904, and a 2N4401.
Well I just happened to have some 2N4401
transistors on hand so I put one in.
Now I've got almost no red! Replace it again,
same story-. Go to my NIE dealer, get the 123AP,
same story-. Finally called Hantarex, got THEIR
transistors, put 'em in, every-thing worked. So
what is my point?
SOLUTION
If you have a Hantarex monitor, and something
blows up, git-aholt-of Hantarex and get the
factory- part. Since this sucker uses European
parts, there is no guarantee that a NTE or SK
part will flll the bill properly.
Murphy's Law #1111
SYMPTOM
Q54 fails several times for no apparent reason.
The wiring of the switches associated with Q54
including flipper end-of-stroke switches indi-
cate no cabling shorts.
PROBLEM
The outhole kicker has a short between one of
the coil wire lugs and the coil stop bracket. This
causes 32VDC to be shorted to the outhole
kicker assembly which, through its metal frame,
will put 32VDC on the switch matrix. Once on
the switch matrix it will get into the CPU and
blow Q54.
SOLUTION
tW1!,tr1l\itliiii
····•~iebWi11i~lc:i11.1&1;1~~t11~f6~··•··
! :l~~ei112·ic1c1 I tr!t\v111
~
0
iflr~
0
~ilce
.!![il~illli\~lllllllf■
NOTE
If this problem is left unresolved, the short
between the coil stop bracket and the coil lug
can cause severe damage to the coil driver
transistor, Q46. Q46 drives both the outhole coil
and the Insert Flash lamp IL. If the transistor
shorts then the Insert Flash lamp will be on
continuously. This can result in severe playfleld
damage due to the large amount of heat that the
flash lamp will generate.
If further assistance is required, please call Pete
or Arnie at 1-800-KICKERS (1-800-542-5377).
Taito US Classic
Me1nory Loss
Sega Super Monaco
GP Extended Play
James Beck
Greater Southern Distributing Co.
Atlanta, Georgia
Dave Cantrell
Sega Enterprises
San Jose, California
SYMPTOM
Your US Classic keeps loosing its mind ( the high
Player can't continue onto 2nd Race (Wet Track)
PROBLEM
scores and other CMOS RAM held stuff).
SOLUTION
SOLUTION/REASON
Player must both qualify for and fmish the 1st
Remove RB from the board. It is located near the
CMOS RAM right on the edge of the board. While
you're at it you had better replace the battery
too. It seems the circuit, as it was designed, pulls
too much juice from the battery and will run
down in a matter of days if the machine is turned
race in the top three to be eligible to continue.
Also, in game option setting, it is recommended
that you set the "Award Super License" to "yes".
This will give you a special award ceremony if
you complete each lap in first place.
off.
The link system, which allows head to head
competition between as many as 8 players, does
not conform to the above rules. While linked the
players are allowed only a qualifying lap and a
single race. This allows all the players to main-
tain on the same level, even if one player is
superior to the others.
NOTE
Since it is a lithium battery no recharging sys-
tem is present.
Kona1ni 's TMNT
Stress Relief
Kevin T. Lee
B & S Music Company
Rome, Georgia
PROBLEM
On Konami's Teenage MutantNirya nutles there
are no stress relief for wires going to the four
joysticks.
SOLUTION
To keep from going crazy with service calls just
to put wires back on the joysticks, I suggest
tightening the terminals on each joystick switch
and adding stress relief to each set of wires to the
joystick. Using a staple gun and wire ties works
very well. Doing this before the game leaves your
shop the first time will save you many trips for
service.
Exclusive Micro-
Prose Preview

Download Page 4: PDF File | Image

Download Page 5 PDF File | Image

Future scanning projects are planned by the International Arcade Museum Library (IAML).

Pro Tip: You can flip pages on the issue easily by using the left and right arrow keys on your keyboard.