7
STAR*TECH JOURNAL/NOVEMBER 1982
Sometimes location owners ( especially in bars)
replace light switches with dimmer rheostats, and
the game is sometimes on the same line. Obviously,
the voltage available to the game is going to drop
dramatically when the dimmer is turned.
In any case, the way to check for correct line
voltage is with your VOM. Set the VOM to 250vac
and stick the probes in the wall receptacle. If it's
OK here, check the transformer primary connec-
tions. If you do not get 11 ?vac, examine the solder
joints on the transformer, fuse block, and interlock
switch. If you do get 11 ?vac, the problem must be
either in the transformer, harness connections, or
in the PCB power supply.
If you suspect the transformer, check its
secondaries with the VOM set to 50vac and
correlate the readings with the legend on the side of
the transformer. The transformer must also be
correctly grounded, so check the ground potential
as well, especially if there is a hum bar rolling up or
down the TV screen.
Harness Problems
Other harness problems include blowing fuses and
malfunctioning controls. The repeating blown-fuse
problem can sometimes be quite exasperating to
solve, for short circuits have the tendency to occur
in areas almost impossible to find. First, try
inserting a new fuse, as old fuses age and may blow
without cause. If the new one also blows, you
definitely have a short.
The best way to approach this problem is by
turning the power off and disconnecting devices
that may be causing the problem, such as the TV,
transformer, and PCB. Disconnect the devices by
pulling off their connectors, but do not allow them
to touch. If necessary, insulate them with small
RANDUSTRIAL
CORPORATION
pieces of electrical tape. Then, connect your VOM
across the terminals of the fuse block ( all electrical
power shut off), and set it to one of the resistance
scales. This will save blowing a fuse each time you
want to check the circuit.
If the VOM reveals that disconnecting the
devices removed the short, reconnect the devices
one by one until the short returns. The last device
connected is the one that is at fault. If the VOM
reads a short even after the devices are discon-
nected, the fault must lie in the harness itself, and
only patient exploration will reveal its location.
First, carefully examine all the wiring, looking for
terminals that may be touching, metal objects such
as coins shorting connections or burned insulation.
If necessary, use the VOM to check each suspected
wire.
Ma/fanctioning Controls
One of the most common problems here is a bad
potentiometer. Typically, a bad pot will cause the
image to jump as it reaches a certain point. The
only cure for this one is to install a new pot.
If a feature that is operated by a switch ( for
example, joysticks, foot pedals, control panel
buttons) does not operate at all, check the switch
with a VOM or continuity tester to verify its
operation. If the switch does not check out, replace
it. If the switch is OK, you should suspect the input
to the switch from the PCB. In this case, get out the
harness and logic schematics and check to see
what kind of input it is. In many cases, the input
will be +5vdc. If so, use the VOM to check its
presence. Normally, the switch is used to pull a
+5vdc line LOW to GND or to pull a LOW line
HIGH. If the PCB output is missing, check the
wire length from the PCB. If you find the signal at
the PCB trace, the wire length or connection is at
fault. If not, begin exploring the PCB using the
logic schematics.
TH
B
STOPS
HERE
LOGIC COMPARATOR $265
Performs in-circuit verification
of proper TTL IC operation
by comparison to a "known-
good '' IC .
A NEW CATALOG ...
INTRODUCES
OVERNIGHT
FLOOR RESURFACER
MAGIC FLOOR is the ideal resurfacer for heavy-
duty trucking aisles. Use indoors or outside.
MAGIC FLOOR is unaffected by rain, snow and
nature's other elements.
MAGIC FLOOR permanently adheres to
concrete, wood, wood block, steel, brick and
asphalt surfaces.
Application is simple. Prime area to be resur-
faced, spread the ready-mixed MAGIC FLOOR
between ¼-inch depth strips. No mixing or troweling
is required. Allow to dry overnight and roll with a
lift truck the next morning. Then open immediately
to normal traffic.
MAGIC FLOOR's special aggregate system
allows for perfect featheredging and the thermo-
plastic binder, unlike cement, provides resiliency
to absorb impact and sound, reducing noise pollution.
For a FREE SAMPLE of MAGIC FLOOR
( sample offer not valid for home use) and a FREE
copy of the 1982-83 Randustrial Maintenance
Catalog, write or call Randustrial Corporation,
13311-NR Union Avenue, Cleveland, Ohio 44120.
Phone 216-283-0300 (in Ohio) or TOLL-FREE
1-800-321-4662 (outside Ohio).
of hard-to-find tools for electronic assembly and
precision mechanics is offered free by Jensen
Tools Inc. The new 144-page catalog features over
2,000 products and introduces several new kits to
the Jensen line of tools.
The contents include tools of interest to field
engineers, technicians, instrument mechanics,
locksmiths, watchmakers, and electronic hobbyists.
Major categories covered include: tool kits and
tool cases, micro-tools, test equipment, soldering
equipment, computer equipment, drafting supplies,
tweezers, screwdrivers, cutters and power tools.
Many of the items are illustrated with full-color
photography.
To obtain your free catalog, write or call:
Jensen Tools, Inc., 7815 South 46th Street,
Phoenix, Arizona 85040 (602) 968-6231.
SIGNATURE ANALYZER $395
Performs simple and
accurate in-circuit trouble-
shooting of RAMs, ROMs,
Microprocessors and other
complex ICs~
BUGTR4P™
INSTRUMENTATION
11 73 Tasman Drive
Sunnyvale. California 94086
C40BJ 734-111 B
• The Signature Analysis Technique is lice nsed from
Hewlett-Packard Co.